8/14/2023 0 Comments Need to make a large beading loomThe more you weave beads with a loom, the better you’ll be able to judge the tension of the warp threads.ĥ. How tight should the tension be on my loom? When setting up your loom, you want your warp threads to have an even tension - not too loose, not too tight. The warp threads are what you will finish off after you’ve finished your beading project and have cut your piece off of your loom.Ĥ. Weft threads get tucked into the beadwork as you go along. The weft threads are what you thread into your needle when you string your beads for weaving. These are the threads that will nestle between your beads when you begin weaving. What’s the difference between warp threads and weft threads? Your warp threads are the threads that you string going up and down on your loom. If you’re creating a piece like an evening bag or something else that needs to hold its shape, you may want to experiment with using Fireline or WildFire beading threads.ģ. I prefer to use my favorite Nymo D on a cone or spool (not a bobbin) for many of the same reasons. Claudia and Elena of Mirrix Looms prefer the C-Lon beading thread because it’s strong, comes in a wide range of colors, and holds up without fraying. What type of thread is best for bead-weaving on a loom? Thread choice is always personal, depending on what kind of bead loom you’re using and what kind of beading project you’re creating. Using a loom for weaving beads also makes it easier to adjust the tension in the beadwork, something that many beginners find difficult when working in square stitch.Ģ. Why weave beads on a loom? Weaving beads on a loom gives you the same look as when you use square stitch, but the actual weaving goes much faster. These points are applicable to any type of loomwork.ġ. Jennifer Van Benschoten had some great tips about loomwork when she wrote about her Mirrix loom a while back. The horizontal kind might be the most familiar–many of us learned on this type as Girl Scouts:īut there are so many other great looms now, too, including the vertical Mirrix loom that makes it really easy to make large-format pieces the Ricks loom, which leaves you with only two warp threads and the Jewel Loom, a portable loom that you can put in your notebook when you aren’t using it! There are many versions of looms you can try. Not relegated to hat bands, belts, and wall hangings made of seed beads anymore, today’s loomwork is bold, trend-focused, and incorporates all sorts of beads, including the two-hole variety. One end with the 3" x 6" glued to the large bottom piece and drilled to allow the eye screws to be screwed in.and repeat on the other end making sure the 4 eye screws are placed evenly across from each other on both ends.There’s an old technique that’s making a big comeback these days–loomwork. (a little confusing I know, but the pic should end any confusion.if not, comment below with any questions and I'll get right back to you or you can also check out the tutorial on the link to "Suzi Craft"s above) Then drill two holes into each small wood piece (and into the bottom large piece) directly in the middle of the 3" x 6" pieces and about 1" in from the sides.and evenly spaced between each other and directly even across the large board to the 3" x 6" wood piece on the other end, so that the eye screws are even on both ends. You want to take your cut wood pieces and apply wood glue to small pieces before placing them on wither end of the large wood piece (as shown). * Drill and drill bit a little smaller then the size of your eye screws * 2 screw-on nuts ( are there any other kind? haha - j/k ) * 4 washers * two 6" bolts (make sure they fit through the eye screws as shown) * 2 Pieces of wood each 1" thick and cut to 2" or 3" x 6" (same width as first board) * a piece of wood that was 1" thick and cut to 6" x 14" It was so easy to make and required very few, inexpensive items from the hardware store.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |